MSRM US754 WiFi Extender Setup

Get Setup

Do you want to extend the wireless network coverage of your existing WiFi router all-around your home or office? Want to boost the WiFi signals? If yes, then just feel relaxed and stop searching anywhere else. You have reached the right spot. With MSRM US754 WiFi extender, you can accomplish this but to achieve this, you just need to complete the MSRM US754 WiFi extender setup. Here, in this article, you will get to know the complete step-by-step instructions for the MSRM US754 setup. 

Instructions For MSRM US754 WiFi Extender Setup Through 192.168.10.1

Go through the below instructions step-by-step for MSRM US754 WiFi extender setup through the IP address 192.168.10.1:

  • Step 1: Make sure that you have turned on your MSRM US754 WiFi range extender and it should be on a repeater.

  • Step 2: Plug in your MSRM extender to the power socket nearer to your wireless router where you actually need to access the web. 

  • Step 3: After that, connect your computer, laptop, or smartphone to your extender either wired or wirelessly. For establishing the wireless connection, you need to go to the WiFi list.

  • Step 4: Thereafter, connect your extender to the MSRM network displayed in the WiFi list.

  • Step 5: For a wired connection, connect the repeater to the computer or PC through an Ethernet cable. Once you complete the setup then remove the cable. 

  • Step 6: After connecting with the MSRM extender, you need to open the program and then enter either ap.setup web address or IP address 192.168.10.1 in the address bar of the web browser.

  • Step 7: Now, you will be navigated to the MSRM US750 extender setup webpage. 

Opticover WiFi Extender Setup Without WPS

  • Step 8: Next, you need to enter the default login credential details in the respective fields. Enter “admin” for both username and password.

  • Step 9: Choose “repeater” from the modes shown on your screen. Choose the network of your desire that you want to extend. Also, enter the password for your chosen network. 

  • Step 10: Follow on-screen instructions carefully. After that, you will see that your MSRM US750 WiFi range extender will start rebooting for approximately 1 minute. 

  • Step 11: At last, connect any WiFi-enabled device to the extended network named SSID_EXT. 

Guidelines For MSRM US754 Extender Setup Through WPS Button

netgear-powerline-1000-setup

Follow the below-mentioned guidelines for the MSRM US754 WiFi extender setup by using the WPS button:

  • Step 1: The first step is to place your MSRM US754 in the same room in which you have placed your wireless router. Make sure to place your extender 5-10 feet away from your extender.

  • Step 2: After that, you need to toggle to set the extender to the “extender mode”.

  • Step 3: Now, you have to wait for some time until the power LED light on your MSRM US754 repeater turns active and stable. Thereafter, press the WPS button on it. 

  • Step 4: Within 2 minutes, press the WPS button on your MSRM extender.

  • Step 5: Next, you will see that the blinking light on the wireless router and extender will stop flashing after 12-15 seconds.

  • Step 6: At last, unplug your extender and spot one of the dead spots to enhance the WiFi signals through the extender. 

Steps For  MSRM US754 Setup As An Access Point 

If you want to set up your  MSRM US754 setup as an access point then you need to have a long Ethernet cable. The access point basically implies that the extender will be associated with the LAN port of the router through Ethernet. It provides better web speed because there is less data loss due to the wired association. Here are the steps:

  • Step 1: Firstly, take an Ethernet cable and connect one end of the Ethernet cable to the LAN port of the router and the other end to the MSRM repeater.

  • Step 2: After that, connect your computer, laptop, or smartphone to the MSRM network in the WiFi list named wireless-AC or Wireless-N.

  • Step 3: Next, you need to open a program on the same device and enter the IP address 192.168.10.1 in the address bar of the web browser. Choose the access mode on your screen. 

  • Step 4: Make sure to start the setup by setting up your extender to the AP mode. 

  • Step 5: In the next step, you need to make a network SSID, password, and the security type for the AP mode.

  • Step 6: Complete the settings and wait for some time until your extender reboots completely. 

  • Step 7: Now, you can connect various WiFi-enabled devices to your extender and can enjoy a seamless internet connection on your device without any hassle.