Setup
Login

Linksys RE7000 Reset

Are you facing issues with your Linksys RE7000 WiFi range extender? Want to know how to Reset Linksys RE7000 Extender? Don’t fret. This blog will assist you. Linksys RE7000 WiFi range extenders boost the WiFi signal strength and eliminate the WiFi signal dead zones. But sometimes, due to technical glitches, users face issues with the Linksys RE7000 WiFi range extender. In that case, you need to reset your Linksys RE7000 WiFi range extender. If you don’t know how to reset the Linksys RE7000 WiFi range, then keep scrolling the blog and follow the below-mentioned step-by-step guidelines to complete the Linksys RE7000 Reset process. Let’s get started.

Reasons to reset the Linksys RE7000 WiFi range extender

Following are the main reasons why you need to reset your Linksys RE7000 WiFi range extender:

  • Overheating or power supply issue.
  • The Linksys RE7000 WiFi range extender is not working correctly.
  • Range extender’s web-based setup page is not accessible.
  • You have forgotten the login credentials.
  • Incorrect configuration or IP address.

Tips to reset the Linksys RE7000 WiFi range extender

Following are the things that you should consider while resetting the Linksys RE7000 WiFi range extender:

  • Place your Linksys RE7000 WiFi range extender in an open and well-ventilated area. 
  • Your extender should receive a sufficient power supply.
  • Disconnect the Bluetooth device.
  • Make sure that your computer or laptop is connected to the device.
  • Check the LED light on the extender.
  • Make the backup of your device’s configuration settings.

Methods to reset the Linksys RE7000 WiFi range extender

There are two methods to reset the Linksys RE7000 WiFi range extender:

  • Hard reset or through reset button.
  • Soft reset or through a web interface.

Method 1: Hard reset of the Linksys RE7000 WiFi range extender

To perform the hard reset of the Linksys RE7000 WiFi range extender, you need to press the reset button for a few seconds. Go through the below-mentioned steps to reset the Linksys RE7000 WiFi range extender by pressing the reset button:

Step 1: First of all, connect your Linksys RE7000 WiFi range extender to the power source and then locate the reset button on the extender.

Step 2: Now, take a sharp pin or paperclip and press the reset button for 8 seconds.

Step 3: When you see a blinking light on the extender, release the button.

Step 4: After that, unplug your Linksys RE7000 WiFi range extender and wait for a few seconds.

Step 5: Complete the power cycle to reset the Linksys RE7000 WiFi range extender.

Method 2: Soft reset of the Linksys RE7000 WiFi range extender

Go through the following steps to perform the soft reset of the Linksys RE7000 WiFi range extender:

Step 1: First of all, plug your Linksys RE7000 WiFi range extender into the wall socket and turn it on.

Step 2: Now, connect your computer or laptop to the WiFi router through an ethernet cable or wirelessly.

Step 3: After that, open any preferred web browser on your device and move to the official website of Linksys extender.

Step 4: Enter your login credentials and navigate to the setup page.

Step 5: Go to the administration tab and select the factory default sub-menu.

Step 6: Then, tap on the “restore factory default” button under the factory default tab and proceed with the next step.

Step 7: After that, unplug your Linksys RE7000 WiFi range extender to power cycle the device.

Step 8: Wait for a few seconds and then reconnect the Linksys WiFi range extender to the power source.

We hope that the steps mentioned above will help you to Reset Linksys RE7000 Extender without any difficulty. Resetting the Linksys RE7000 WiFi range extender to factory default settings will remove the personalized settings. Still, if you are facing any issues with the Linksys RE7000 Reset, then feel free to contact our technical experts.